Calcium and magnesium salts determine water hardness, which is mainly responsible for scaling and damage to water systems, boilers, kettles, faucets and appliances. If the water has a hardness of more than 15 French degrees, it is a good idea to install an ion exchange softener.
GEL DECAL - Version M is a double body ion exchange water softener for drinking water (conf . DM 25/2012): the brine vat is separate from the cylinder unit. UP-FLOW regeneration is designed to contain consumption (about 0.096 kg salt/L resin and 4.2 L water/L resin).
MAIN FEATURES.
- Dual body softener: salt vat separate from the canister
- High-efficiencyUP-FLOW regeneration (reduced water and salt consumption)
- Dedicatedcontrol head for M models ( VF95 series)
- Built-inmixing valve and by-pass (up to 75 L, depending on model)
- Potable and technological use: suitable materials according to DM 174/2004
SPECIFICATIONS AT A GLANCE
Connections: male (depending on model) | Operating pressure: 2-6 bar | Water temperature: 5-30 °C | Ambient temperature: 5-50 °C.
For correct sizing (flow rate, resin volume, cyclic capacity) refer to the DECAL model technical table.
Water softener gel decal 110m - double body standard ion exchange
Calcium and magnesium salts determine water hardness, which is mainly responsible for scaling and damage to water systems, boilers, kettles, faucets and appliances. If the water has a hardness of more than 15 French degrees, it is a good idea to install an ion exchange softener.
GEL DECAL - Version M is a double body ion exchange water softener for drinking water (conf . DM 25/2012): the brine vat is separate from the cylinder unit. UP-FLOW regeneration is designed to contain consumption (about 0.096 kg salt/L resin and 4.2 L water/L resin).
MAIN FEATURES.
- Dual body softener: salt vat separate from the canister
- High-efficiencyUP-FLOW regeneration (reduced water and salt consumption)
- Dedicatedcontrol head for M models ( VF95 series)
- Built-inmixing valve and by-pass (up to 75 L, depending on model)
- Potable and technological use: suitable materials according to DM 174/2004
SPECIFICATIONS AT A GLANCE
Connections: male (depending on model) | Operating pressure: 2-6 bar | Water temperature: 5-30 °C | Ambient temperature: 5-50 °C.
For correct sizing (flow rate, resin volume, cyclic capacity) refer to the DECAL model technical table.
Calcium and magnesium salts determine water hardness, which is the main culprit in scaling and damage to fixtures, heat generators, faucets and appliances. If the hardness is greater than 15° French, installing an ion exchange softener is also an effective choice to reduce energy consumption and detergents, improving comfort and protection of the system.
GEL DECAL - Version M is a double body ion exchange softener for potable water (conf . DM 25/2012): the brine vat is separate from the cylinder unit. The structure is designed for high performance and ease of maintenance, with UP-FLOW regeneration that contributes to the containment of consumption (approximately 0.096 kg of salt/L resin and 4.2 L of water/L resin).
STRUCTURE AND OPERATION
- Ion exchange with cationic resins for hardness reduction
- Double body: resin cylinder + separate brine vat
- Plastic materialcylinder coated with fiberglass
- Control head for M models ( VF95 series)
- Built-inmixing and by-pass (up to 75 L, depending on model)
EQUIPMENT
- Control head (VF95 series for M models)
- Cationic resins
- Brine vat
- Discharge line for regeneration
- Hydraulic components for by-pass/mixing connection and management
TECHNICAL DATA (GENERAL RANGES - M VERSION)
- Operating pressure: 2 - 6 bar
- Water temperature: 5 - 30 °C
- Ambient temperature: 5 - 50 °C
- Connections: male (depending on model)
- Flow rate / Resins / Cyclic capacity: variable according to DECAL model (see technical table)
INSTALLATION
- Install by qualified personnel in a dry place, protected from frost and sunlight
- Prepare 230 V power outlet
- Install a safety filter upstream of the softener
- Use flexible hoses or vibration-dampening couplings for plumbing connections
- Place a free drain (not under pressure) at a lower height than the vat overflow
- With pressures < 2 bar install an autoclave; with pressures > 6 bar install a pressure reducer
- Install a check valve after the meter
- For potable use: adjust mixing to achieve residual hardness 15 °f
INSTALLATION DIAGRAM
The schematic shows main line, by-pass, safety filter, drains, and mixing for potable use.
COMPONENTS SHOWN IN THE DIAGRAM:
- 1. Counter
- 2. Pressure reducer
- 3. Check valve
- 4. Upstream shutoff valve
- 5. Raw water withdrawal tap
- 6. Safety filter
- 7. Filtered water diversion for other uses
- 8. Spout connection
- 9. By-pass faucet
- 10. Aeration valve (only for some models)
- 11. Flexible fittings
- 12. Header
- 13. Cylinder
- 14. 230 V power supply unit
- 15. Salt vat
- 16. Drains
- 17. Softened water withdrawal tap
- 18. Downstream shutoff valve
- 19. Anti-scale dispenser
- 20. Mixing valve
MAINTENANCE
- Periodic cleaning of upstream filter cartridge
- Cleaning of the brine vat every 6 months
- Checking and replenishing salt as directed by the technician
- Checking water hardness delivered every 2 months
- Checking that the salt level in the vat is above the water level
RECOMMENDED ACCESSORIES
- RESICLEAN - resin cleaner/regenerator (promotes removal of inorganic deposits; ready to use after dilution)
- BRAND
- GEL
- ALIMENTATION (V.)
- 230
- CAPACITY
- 1180
Services that makes difference
24/48H shipping
Ultra-fast shipping with express courier, to offer excellent and timely service to our customers.
Secure payments
We ensure maximum security in online payments through advanced transaction protection systems for the peace of mind of our customers.
Pay in 3 installments with PayPal
Choose the convenience of paying in three interest-free installments with PayPal. An option designed for your financial flexibility.